RaspberryPi/Wireless - Revision history

Admin: Replaced content with "See Linux/Wireless/1 for method 1 and Linux/Wireless/2 for method 2. {{PiFlag}} {{KaliFlag}} {{LinuxFlag}}"

2017-08-12T23:58:49Z

Replaced content with "See Linux/Wireless/1 for method 1 and Linux/Wireless/2 for method 2. {{PiFlag}} {{KaliFlag}} {{LinuxFlag}}"

@@ Line 1: / Line 1: @@
-=The Method (This Works)=
+See [[Linux/Wireless/1]] for method 1 and [[Linux/Wireless/2]] for method 2.
-To connect to a WPA wireless network from a Raspberry Pi:
+{{PiFlag}}
+{{KaliFlag}}
-First add network configuration to /etc/wpa_supplicant/wpa_supplicant.conf
+{{LinuxFlag}}

Admin at 04:14, 20 August 2016

2016-08-20T04:14:24Z

← Older revision		Revision as of 04:14, 20 August 2016
Line 1:		Line 1:
	=The Method (This Works)=		=The Method (This Works)=

	To connect to a WPA wireless network from a Raspberry Pi:		To connect to a WPA wireless network from a Raspberry Pi:

Admin at 03:58, 30 July 2016

2016-07-30T03:58:22Z

← Older revision		Revision as of 03:58, 30 July 2016
Line 1:		Line 1:
			=The Method (This Works)=
	To connect to a WPA wireless network from a Raspberry Pi:		To connect to a WPA wireless network from a Raspberry Pi:

Line 68:		Line 69:
	-D nl80211,wext -c /etc/wpa_supplicant/wpa_supplicant.conf		-D nl80211,wext -c /etc/wpa_supplicant/wpa_supplicant.conf
	</pre>		</pre>

			=The Need for Improvement=

			While the method above works, it doesn't seem to connect to networks automatically, at boot. Maybe add the ifdown ifup commands to /etc/rc.local.

Admin at 23:10, 29 July 2016

2016-07-29T23:10:01Z

← Older revision		Revision as of 23:10, 29 July 2016
Line 60:		Line 60:
	<pre>		<pre>
	ifconfig		ifconfig
			</pre>

			To start wpa_supplicant manually:

			<pre>
			# sudo /sbin/wpa_supplicant -P /var/run/wpa_supplicant.wlan0.pid -i wlan0 \
			-D nl80211,wext -c /etc/wpa_supplicant/wpa_supplicant.conf
	</pre>		</pre>

Admin at 23:09, 29 July 2016

2016-07-29T23:09:39Z

@@ Line 41: / Line 41: @@
 wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
 iface default inet dhcp
 </pre>

Admin: Created page with "To connect to a WPA wireless network from a Raspberry Pi: First add network configuration to /etc/wpa_supplicant/wpa_supplicant.conf

 ctrl_interface=DIR=/var/run/wpa_su..."

2016-07-29T23:08:46Z

Created page with "To connect to a WPA wireless network from a Raspberry Pi: First add network configuration to /etc/wpa_supplicant/wpa_supplicant.conf <pre> ctrl_interface=DIR=/var/run/wpa_su..."

New page

To connect to a WPA wireless network from a Raspberry Pi:

First add network configuration to /etc/wpa_supplicant/wpa_supplicant.conf

<pre>
ctrl_interface=DIR=/var/run/wpa_supplicant GROUP=netdev
update_config=1

network={
ssid="Your SSID Here"
proto=RSN
key_mgmt=WPA-PSK
pairwise=CCMP TKIP
group=CCMP TKIP
psk="YourPresharedKeyHere"
}
</pre>

Next edit /etc/network/interfaces and modify the wlan0 entry.

If you have a static IP:

<pre>
# ------ Static IP --------
###allow-hotplug wlan0
iface wlan0 inet manual
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
iface default inet static
address 10.1.2.20
netmask 255.255.255.0
network 10.1.2.0
gateway 10.1.2.1
</pre>

If you have an automatically-assigned IP from the DHCP controller:

<pre>
# ------- DHCP ------------
###allow-hotplug wlan0
iface wlan0 inet manual
wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf
iface default inet dhcp
</pre>