Widy/Ethernet Gateway - Revision history

Admin: /* Firewall */

2018-01-20T16:35:36Z

Firewall

← Older revision		Revision as of 16:35, 20 January 2018
Line 71:		Line 71:

	Now set a firewall rule that will allow traffic to pass between these devices:		Now set a firewall rule that will allow traffic to pass between these devices:
	* Go to Network > Firewall > ~~SEttings~~		* Go to Network > Firewall > Settings
	* Zones > ADd		* Zones > ADd
	* Name: lan2wan		* Name: lan2wan

2018-01-20T16:35:04Z

2018-01-20T16:34:36Z

2018-01-20T16:34:16Z

← Older revision		Revision as of 16:34, 20 January 2018
Line 1:		Line 1:
			This describes how to configure Widy and OpenWrt for the following configuration:

			<pre>
			Client1
			:
			: (wireless connection)
			:
			Widy ---------------------------- Internet Source
			: (ethernet connection)
			:
			: (wireless connection)
			:
			Client2
			</pre>

	==Steps==		==Steps==

2018-01-20T16:27:47Z

Wifi

← Older revision		Revision as of 16:27, 20 January 2018
Line 16:		Line 16:

	Next, set up the lan and wireless interfaces.		Next, set up the lan and wireless interfaces.

			[[Image:WidyWifiList.png\|500px]]

	===Interfaces===		===Interfaces===

2018-01-20T16:26:27Z

Wireless interface

← Older revision		Revision as of 16:26, 20 January 2018
Line 30:		Line 30:
	* Netmask: 255.255.255.0		* Netmask: 255.255.255.0
	* everything else blank		* everything else blank

			[[Image:WidyEthernetGatewayWifiSettings.png\|500px]]

	Under DHCP server, make sure that you enable a DHCP server. No other configuration is necessary.		Under DHCP server, make sure that you enable a DHCP server. No other configuration is necessary.

	[[Image:~~WidyEthernetGatewayWifiSettings~~.png\|500px]]		[[Image:WidyEthernetGatewayDHCPSettings.png\|500px]]

	End result will look like this:		End result will look like this:

2018-01-20T16:25:12Z

Interfaces

← Older revision		Revision as of 16:25, 20 January 2018
Line 32:		Line 32:

	Under DHCP server, make sure that you enable a DHCP server. No other configuration is necessary.		Under DHCP server, make sure that you enable a DHCP server. No other configuration is necessary.

			[[Image:WidyEthernetGatewayWifiSettings.png\|500px]]

	End result will look like this:		End result will look like this:

2018-01-20T16:24:23Z

LAN interface

← Older revision		Revision as of 16:24, 20 January 2018
Line 41:		Line 41:
	Modify the LAN interface so that it acts as a client rather than a server. The ethernet cable will be plugged into an internet-providing device (such as another router), and will be assigned an IP accordingly, so tell the LAN interface to act as a DHCP client.		Modify the LAN interface so that it acts as a client rather than a server. The ethernet cable will be plugged into an internet-providing device (such as another router), and will be assigned an IP accordingly, so tell the LAN interface to act as a DHCP client.

	[[Image:WidyEthernetGatewayLanDhcp.png\|~~500px~~]]		[[Image:WidyEthernetGatewayLanDhcp.png\|400px]]

	===Firewall===		===Firewall===

2018-01-20T16:24:10Z

Interfaces

← Older revision		Revision as of 16:24, 20 January 2018
Line 19:		Line 19:
	===Interfaces===		===Interfaces===

	When you first start out, there will likely only be a br-lan device. You will need to create a wireless interface.		When you first start out, there will likely only be a br-lan device. You will need to create a wireless interface and modify the lan interface.

			====Wireless interface====

	Create a wireless interface "wifinet" that will represent the interface used to create/connect to clients on the wifi network.		Create a wireless interface "wifinet" that will represent the interface used to create/connect to clients on the wifi network.
Line 34:		Line 36:

	[[Image:WidyEthernetGatewayInterfaces.png\|500px]]		[[Image:WidyEthernetGatewayInterfaces.png\|500px]]

			====LAN interface====

			Modify the LAN interface so that it acts as a client rather than a server. The ethernet cable will be plugged into an internet-providing device (such as another router), and will be assigned an IP accordingly, so tell the LAN interface to act as a DHCP client.

			[[Image:WidyEthernetGatewayLanDhcp.png\|500px]]

	===Firewall===		===Firewall===

2018-01-20T16:21:28Z

Interfaces

← Older revision		Revision as of 16:21, 20 January 2018
Line 19:		Line 19:
	===Interfaces===		===Interfaces===

	When you first start out, there will likely only be a br-lan device.		When you first start out, there will likely only be a br-lan device. You will need to create a wireless interface.

	Create a wireless interface "wifinet" that will represent the interface used to create/connect to clients on the wifi network.		Create a wireless interface "wifinet" that will represent the interface used to create/connect to clients on the wifi network.
Line 30:		Line 30:

	Under DHCP server, make sure that you enable a DHCP server. No other configuration is necessary.		Under DHCP server, make sure that you enable a DHCP server. No other configuration is necessary.

			End result will look like this:

			[[Image:WidyEthernetGatewayInterfaces.png\|500px]]

	===Firewall===		===Firewall===